220V Semi Automatic PCB Lead Wire Cutting Machine Including a Special-use Blade

Description

220V  Semi automatic PCB foot cutting machine
Question:
Please let me know what is the max board width it can take?
Answer:
The maximum cutting width is 200 mm
Notice: We send a blade(0) as a gift.
The breadboard wipe cutting machine is mainly applied in cutting the unwanted pin after the welding of parts of apparatus and this machine is assembled by parts made with exquisite craftwork. The key parts are dealt with grinding , and the imported bearing assembled wipe cutting machine grinding consistency is excellent, the rotating   speed of blade is fast and is very efficient and convenient to operate with   little noise. The double lead rail is adjusted synchronously , the height of wipe cutting is adjustable and the outlook is attractive. “Continuous improvement, lasting and efficient, clients first” is our quality tenet, it is our honor to serve you.
Instruction of adjusting
1.Open the package and read the instruction carefully and check the accessories (refer to term 7 in the instruction)
2.Check the body of machine for any abnormal phenomena, if so , contact the local agent as soon as possible
3.After conforming the good connection of the case earth, plug in.
4.First adjust the double lead rail travel route biggest, unscrew the gland bush screw(gland bush screw is right-handed screw )with 8# inner hexagonal wrench counterclockwise,take out the blade gland bush and clean up both sides of tool apron, blade, gland bush with clean and soft cloth. Then place gently the blade on the base(surface up). Next ,place the blade gland bush on the blade, screw down the gland bush screw with 8# inner hexagonal wrench clockwise. When unloading the blade, use the enclosed dismantled stick to fix the tool apron.
5. Rotate the adjusting hand wheel, adjust the width between the lead rails, and place one wanted placode of wipe cutting machine on the entrance and exit port respectively. Rotate the hand wheel until the placode at both ports slide properly in the lead rail.
6.Four sets(three screws per set)assembling screws that are equipped on top of lead rail bland bush are used to adjust the thickness of placode. During the adjusting first unscrew three perch screws among them and put placode inside and then adjust two lower order screws besides until they fit and screw down the middle screw. Operation are the same for four sets and adjust placode to slide properly inside the lead rail
7.Adjusting of height of wipe cutting machine : screw down lead rail retaining screw and adjust the big screw cap until the distance between blade and lead rail meets the requirement then screw down lead rail retaining screw. When adjusting lower avoid any friction between lead rail and blade for fear of damage to blade.
8. The height of wipe cutting of wipe cutting machine was adjusted as 1.5mm when it leaves factory and the thickness of textile board was adjusted as 1.2mm. When adjusting is necessary please adjust according to method mentioned above.
Features
Blade jitter small
Pin cutting leveling
The 3 hole blade gland uses the triangle positioning principle, the blade is firmly fixed, not easy to loose, the high speed running condition, the blade does not slip, the operation is smooth, the cutting foot is accurate, the safety factor is high.
The whole machine is steady, low noise and low jitter.
The feeding guide rail of the fine steel is of high thickness, wear resistance, not easy to deform and prolong the service life of the machine.
Line type cutting.
Specifiction
Operations
1. Place the welded breadboard on the adjusted wipe cutting machine and insert the lead rail down the leading-in of lead rail.
2.Push dexter feed hand shank and push placode advance at constant speed
3.Repeat step 1,2 and finish cutting the welded placode.
Notice: When the placode moves avoid moving too fast, and moving too fast can directly shorten the use life of blade and even endanger safety.
Maintenance
Wipe cutting machine is the mechanic equipment of high accuracy and with high speed and the constant maintenance prolongs its use life
1.The rotating part needs constant lubrication.
2.Clean up the cut pin
3.If the transmitting triangle strap is damaged, it needs immediate replacement and the specification is (0-450)
4.The blade should not leave cutter head for too long, lubricate the cutter head when necessary if it leaves for several days.
Notice
1.When the machine is in operation avoid putting hands into the machine.
2. This machine must work in the state of good earth connection
3.Cut off the power when installing or dismantling blade or in case of emergency
4.Cut off the power in sace of a blackout.
5.This machine should not be used in humid, flammable, corrosive, dense bug dust-filled environment.
6. Non professional repairmen are not allowed to dismantle the cover to repair it personally .
7.Do not open the cover when the machine rotates.
8.Operate the machine according to instruction strictly; otherwise out factory takes no responsibility.
Item Include
(151005)
A set of 220V  Semi automatic PCB foot cutting machine
A set of Blade
Shipping & Handling Details
Default  Shipping Cost or Free Shipping Information:
▲
Default  shipping cost or free shipping service is only for the customers  from Canada or the lower 48 United States by Canada Post, USPS or  the UPS Ground. Customers from other areas or needs other shipping  ways, please contact us.
▲
Buyers  from Guam, Puerto Rico, Virgin Islands, American Samoa, Alaska,  Hawaii, PO Boxes, APO/FPO addresses or other countries/areas, there  WILL be extra shipping costs, please contact us for more detailed  information.
▲
Please  make sure your address is valid for both UPS and USPS services. Any  costs incurred because of incorrect or undeliverable address should  be undertaken by buyer.
Handling Time:
Shipping  is usually made in 1-3 business days after payments cleared. Orders  are processed from Monday-Friday; Not on the weekends & public  holidays.
Sales tax / Customs  duties:
Any  sales taxes or Customs duties are not included. If came out, they  must be undertaken by the buyer.
Damage In Shipping:
Email  or call us First! We will work with you to get the case resolved in  the fastest method.
Return /  Refund
If you are not 100% happy with your purchase, please  contact Us. Please don't directly opened a request or case without  informing us, or else, we will do some discounts on the warranty and  other sales-services later on. Hope for your understanding.
Returns & Exchanges
▲
All  returns must be made within 14 days of delivery date. Items must be  in new, unused condition, with all original materials included with  the shipment. A partial refund may be applied for opened or damaged  items, depending on the condition.
▲
Items  returned under the buyer’s remorse: The return shipping fee must be  covered by the buyer; The original shipping cost will also be  deducted from the refund. 15% restocking fee of the items purchase  price will be charged.
▲
Returns  that are the result of our seller's error: Buyer will receive a full  refund of the item as well as shipping charges
▲
All  returns require a RA (Return Authorization) number that will be  given by our seller. Please contact with us at first for more  details.
Defective & Damaged Products
▲
If  product was received damaged or not as described, please send us  some pictures or videos, so we could well understand your problem,  then solve them for you ASAP. Besides, it's much helpful for us to  claim with UPS, remind our related department to pay much more  attention to packaging later on. Hope for your understanding.
▲
Replacement  or refund of defective or damaged products can only be returned in  exchange for the exact same product, or else, the purchase price  will be refunded back to your original payment method.
▲
If  an item is received damaged, customer service must be contacted  within 7 days of receiving your item. All returns require a RA  (Return Authorization) number as above.
Payment
eCheck Issues:
Payments via  eCheck do not clear immediately. Usually you will wait 5-7 days  after checkout for it to clear. Then we will arrange shipments  for you.
Warranty & Feedback
▲
6  months' warranty for the machines, not for the consumables. We stand  behind our products all the item, so even if your warranty period  has expired, you can still seek for service or technical support  from us with low cost.
▲
Any  warranty shipping cost to us is responsible by buyer.
▲
Any  shipping cost to buyer is responsible by the seller.
▲
We  committee to the customer satisfaction and want to bring you the  best purchase experience. If there is any problems, please contact  us ASAP. If not, please leave us a positive feedback as it's very  important for us. Thanks very much.