Auto Pilot Hydroponic Greenhouse Room CO2 4 Burner Generator Natural Gas US

Description

Summarization:
CO2 generator main uses in plant vegetables，increase CO2 content for vegetable and flower planting in greenhouse.
It is an
ideal greenhouse product for accelerating plant growth,
increasing yield, improving quality and can enhancing
disease-resistance. This 4 burner CO2 generator can
produce 3-13 cubic feet per hour. The W4B is
recommended for areas under 3200 cubic feet.
NOTE: An air exchange is recommended when using
CO2 generators. At least once every hour to avoid your
plants from getting CO2 poisoning.
The W4B used an automatic electronic ignition module.
When ignite unsuccessfully, the solenoid valve can
automatically prevent the gas from leaking out in the
event. A standard tip over switch is one of the safety
features of the W4B.
Also, comes standard with 4 brass burners and a 12 foot
hose. A regulator is provided, so that you can connect or
tap into existing lines.
Reducing Burners
The W4B CO2 generator installed four burners, you can reduce them as needed, front panel can be removed.
Four screws are used to secure the panel in place. Simply loosen the screws and lift the panel off the keyhole in
order to expose the burner assembly. Be sure to replace the cover prior to operating.
Natural Gas Generators Only
NOTE: It is very important to install the regulator “in-Line” between your gas supply and generator. The
regulator supplied with the W4B-NG is present to maintain a constant pressure of 4.5” WC. Which is around ¼
PSI. Before installation, verify your main gas pressure. Most Gas companies install low pressure gas regulators
at the meter that are about ½ PSI. Some commercial buildings have a high pressure gas main (usually around 2
PSI). If the pressure is high, it will need to be reduced to ½ PSI or lower before installing regulator (high
pressure can keep the valves open, causing unit to run with no power).
4) When installing, make sure to install a gas shut-off valve on your line (turn off at main or meter). Install the
shut-off valve in an accessible location. Install the in-line regulator to the gas supply (3/8” NPT female thread).
Connect the hose to the flared fitting on regulator. Using two crescent wrenches or similar to tighten
connections.
5) Open the inline shut off valve (make sure the main is on). Check for leaks using soapy water and a spray
bottle. Look for bubbling, this indicates a leak.
6 ) Flip power switch to on position, within 20 sec. unit will begin to spark to ignite the fuel
Connecting to CO2 controller
NOTE: The recommended CO2 level for optimum growth is between 1000 to 1500 PPM. Above these levels
is considered wasteful. Above 5000 PPM is considered dangerous to animals and humans. Side effects of
excessive CO2 include headache, drowsiness & shortness of breath. Use a PPM controller to ensure you’re
maintaining proper PPM levels.
1) Connect the CO2 generator’s power supply to the controller that you are using. Usage of the generator
should be during lights ON hours. At bare minimum, a timer can be used to turn the generator on/off.
Possibilities are likely to exceed recommended PPM range with this method.
2) Set CO2 controller to desired PPM level and plug in the power of the CO2 generator into the controller.
Natural Gas Pressure: 4.5” WC
Total BTU 1 burner: Natural Gas 3,135
Total BTU 2 burner: Natural Gas 6,270
Total BTU 3 burner: Natural Gas 9,405
Total BTU 4 burner: Natural Gas 12,540
Dimensions: 11”x16 ½” x 8 1/2”
WARNING: Not recommended for use inside of a Grow tent. The high heat can cause melting of the wall material.
THis is only for Natural Gas ,This will not work with  LP Propane Gas.
On Jul-25-21 at 19:31:12 PDT, seller added the following information: