Intbuying 220V Auto Circuit Board PCB Cut Foot Machine Lead Wire Cutting Machine

Description

220V Semi-automatic PCB Foot Cutting Machine
The breadboard wipe cutting machine is mainly applied in  cutting the unwanted pin after the welding of parts of  apparatus and this machine is assembled by parts made  with exquisite craftwork. The key parts are dealt with  grinding , and the imported bearing assembled wipe  cutting machine grinding consistency is excellent, the  rotating   speed of blade is fast and is very efficient  and convenient to operate with   little noise. The  double lead rail is adjusted synchronously , the height  of wipe cutting is adjustable and the outlook is  attractive. “Continuous improvement, lasting and  efficient, clients first” is our quality tenet, it is  our honor to serve you.
Instruction  of adjusting:
1.Open the package and read the  instruction carefully and check the accessories (refer  to term 7 in the instruction)
2.Check the body of machine for any abnormal phenomena,  if so , contact the local agent as soon as possible
3.After conforming the good connection of the case  earth, plug in.
4.First adjust the double lead rail travel route  biggest, unscrew the gland bush screw(gland bush screw  is right-handed screw )with 8# inner hexagonal wrench  counterclockwise,take out the blade gland bush and clean  up both sides of tool apron, blade, gland bush with  clean and soft cloth. Then place gently the blade on the  base(surface up). Next ,place the blade gland bush on  the blade, screw down the gland bush screw with 8# inner  hexagonal wrench clockwise. When unloading the blade,  use the enclosed dismantled stick to fix the tool apron.
5. Rotate the adjusting hand wheel, adjust the width  between the lead rails, and place one wanted placode of  wipe cutting machine on the entrance and exit port  respectively. Rotate the hand wheel until the placode at  both ports slide properly in the lead rail.
6.Four sets(three screws per set)assembling screws that  are equipped on top of lead rail bland bush are used to  adjust the thickness of placode. During the adjusting  first unscrew three perch screws among them and put  placode inside and then adjust two lower order screws  besides until they fit and screw down the middle screw.  Operation are the same for four sets and adjust placode  to slide properly inside the lead rail
7.Adjusting of height of wipe cutting machine : screw  down lead rail retaining screw and adjust the big screw  cap until the distance between blade and lead rail meets  the requirement then screw down lead rail retaining  screw. When adjusting lower avoid any friction between  lead rail and blade for fear of damage to blade.
8. The height of wipe cutting of wipe cutting machine  was adjusted as 1.5mm when it leaves factory and the  thickness of textile board was adjusted as 1.2mm. When  adjusting is necessary please adjust according to method  mentioned above.
Features:
Blade jitter small
Pin  cutting leveling
The 3 hole blade gland uses the triangle  positioning principle, the blade is firmly fixed, not easy  to loose, the high speed running condition, the blade does  not slip, the operation is smooth, the cutting foot is  accurate, the safety factor is high.
The  whole machine is steady, low noise and low jitter.
The  feeding guide rail of the fine steel is of high thickness,  wear resistance, not easy to deform and prolong the service  life of the machine.
Line type  cutting.
Specifiction:
Notice: We send a  blade(0) as a gift.
Operations:
1. Place the welded breadboard on the adjusted wipe  cutting machine and insert the lead rail down the leading-in of lead  rail.
2.Push dexter feed hand shank and push placode advance at constant  speed
3.Repeat step 1,2 and finish cutting the welded placode.
Notice: When the placode moves avoid moving too fast, and moving too  fast can directly shorten the use life of blade and even endanger  safety.
Maintenance:
Wipe  cutting machine is the mechanic equipment of high accuracy and with  high speed and the constant maintenance prolongs its use life
1.The rotating part needs constant lubrication.
2.Clean up the cut pin
3.If the transmitting triangle strap is damaged, it needs immediate  replacement and the specification is (0-450)
4.The blade should not leave cutter head for too long, lubricate the  cutter head when necessary if it leaves for several days.
Notice:
1.When the machine is in operation avoid putting hands into the  machine.
2. This machine must work in the state of good earth connection
3.Cut off the power when installing or dismantling blade or in case  of emergency
4.Cut off the power in sace of a blackout.
5.This machine should not be used in humid, flammable, corrosive,  dense bug dust-filled environment.
6. Non professional repairmen are not allowed to dismantle the cover  to repair it personally .
7.Do not open the cover when the machine rotates.
8.Operate the machine according to instruction strictly; otherwise  out factory takes no responsibility.
Item Include
(151005)
A  set of 220V  Semi automatic PCB foot cutting machine
A set of Blade
新建网页 2
Shipping & Handling  Details
Default Shipping Cost or Free  Shipping Information:
▲
Default  shipping cost or free shipping service is only for the lower 48 United  States by UPS Ground or USPS. Other areas or needs other shipping ways,  please contact us.
▲
Buyers  from Guam, Puerto Rico, Virgin Islands, American Samoa, Alaska, Hawaii,  PO Boxes, APO/FPO addresses or other countries/areas,
there  WILL be extra shipping costs, please contact us for more detailed  information.
▲
Please  make sure your address is valid for both UPS and USPS services. Any  costs incurred because of incorrect or undeliverable address should be  undertaken by buyer.
Handling Time:
Shipping  is usually made in 1-3 business days after payments cleared. Orders are  processed from Monday-Friday; Not on the weekends & public holidays.
Sales tax /  Customs duties:
Any  sales taxes or Customs duties are not included. If came out, they must  be undertaken by the buyer. Sales Tax of 8% will be applied for orders  shipped within the state of California.
Damage In  Shipping:
Email or  call us First! We will work with you to get the case resolved in the  fastest method.
Return / Refund
If you are not 100% happy with your  purchase, please contact Us. Please don't directly opened a request or  case without informing us, or else, we will do some discounts on the  warranty and other sales-services later on. Hope for your understanding.
Returns & Exchanges
▲
All  returns must be made within 14 days of delivery date. Items must be in  new, unused condition, with all original materials included with the  shipment. A partial refund may be applied for opened or damaged items,  depending on the condition.
▲
Items  returned under the buyer’s remorse: The return shipping fee must be  covered by the buyer; The original shipping cost will also be deducted  from the refund. 15% restocking fee of the items purchase price will be  charged.
▲
Returns  that are the result of our seller's error: Buyer will receive a full  refund of the item as well as shipping charges
▲
All  returns require a RA (Return Authorization) number that will be given by  our seller. Please contact with us at first for more details.
Defective & Damaged Products
▲
If  product was received damaged or not as described, please send us some  pictures or videos, so we could well understand your problem, then solve  them for you ASAP. Besides, it's much helpful for us to claim with UPS,  remind our related department to pay much more attention to packaging  later on. Hope for your understanding.
▲
Replacement  or refund of defective or damaged products can only be returned in  exchange for the exact same product, or else, the purchase price will be  refunded back to your original payment method.
▲
If  an item is received damaged, customer service must be contacted within 7  days of receiving your item. All returns require a RA (Return  Authorization) number as above.
Payment
eCheck Issues:
Payments  via eCheck do not clear immediately. Usually you will wait 5-7 days  after checkout for it to clear. Then we will arrange shipments for  you.
Warranty & Feedback
▲
6  months' warranty for the machines, not for the consumables. We stand  behind our products all the item, so even if your warranty period has  expired, you can still seek for service or technical support from us  with low cost.
▲
Any  warranty shipping cost to us is responsible by buyer.
▲
Any  shipping cost to buyer is responsible by the seller.
▲
We  committee to the customer satisfaction and want to bring you the best  purchase experience. If there is any problems, please contact us ASAP.  If not, please leave us a positive feedback as it's very important for  us. Thanks very much.
On May-30-21 at 23:37:59 PDT, seller added the following information: